slideklion.blogg.se - Deadlock coatings

If you have specific questions about Cerakote or photos of something you want to be done please email to along with your order number. Put color or color pattern combo in ORDER COMMENTS. Firing pin channel sleeve included with the slide Includes SLR billet Gen 3/4 specific back plate (Black Hardcoat Anodize) How you wash your vehicle is the most important part of maintaining your ceramic coating.Includes Billet SLR top plate (Black Hardcoat Anodize) If your vehicle gets hit by sprinkles, wipe it down with Eco Shine water-less wash ASAP to prevent the minerals in the water from etching the coating. Following our proper washing methods as shown in our diagram along with following the maintenance schedule will help prevent visual damage to your coating.

A - Ceramic Coating is harder than your vehicles paint so it does provide superior protection against swirls and water spotting BUT these things can still happen if you are negligent with how you care for the coating.

Q - Can you still get swirls and will you still get water spots?.

If water contact happens, make sure you dry the vehicle to avoid any water spotting. It's best to avoid water contact during this period if possible.

A - Coating is fully cured and hardened after 72 hours.

After (1) hour you can stack the coating with another layer if you choose or wipe down with Punch-It synergy spray to make the surface even slicker!

A - Coating is dry within (1) hour of application.

We have applied up to (3) coats at our detail shop and it's AMAZING.

A - Heck ya you can! Make sure you wait (1) hour in between coats.

Q - Can you apply multiple coats? And how many?.

Follow the same removal process as with the paint.

A - Yes, but in the same manner as the gel coat mentioned above, you want to apply (2) coats because the first coat gets absorbed into the pores of the trim.

This will give you excellent protection and hydrophobic properties.

A - Yes but we recommend applying (2) coats since the first coat absorbs into the pores of the gel coat.

Q - Can you apply to gel coat boats, wave runners, etc.

A - (4-5) small vehicles or (3-4) full-size vehicles.

Q - How many vehicles can you coat with a 100ml bottle?.

Our Slick Back primer polish will usually remove any product that was left on the paint too long.

Applying in hotter conditions will give you a shorter time frame before you wipe-off.

Applying in colder conditions will give you a longer time frame before wipe-off.

If you have difficulty removing the product, you waited too long. This slight resistance lets you know it’s ready for removal. The coating will have some slight resistance when you wipe. How do you know it’s ready to be removed? Perform a test spot with your microfiber towel.

Do not go back into an area minutes later and re-wipe or you could cause streaking.Ĭeramic coating maintenance schedule found here Once you have wiped with the second towel the coating will begin to “set-up”. Using an additional towel, lightly wipe over the area again to ensure product is even and level on the surface. Give it 45-60 seconds to set up and then remove using a clean microfiber towel. Product will have an “oil slick/rainbow” look to it as it begins to dry. Apply directly onto the applicator pad and spread product evenly onto the surface. Wipe down the surface with Throw Back paint cleanser to remove any oils/residue left from your polishing step.Īpply: Shake Beadlock Pro well. Polish the paint to reduce any surface defects and create maximum gloss. Prep: Decontaminate the paint surface using Smooth Move paint decontaminater followed by claying the surface with a clay bar and Shine Mist clay lube. Purchase a Beadlock Pro sticker for your car door here!

Product may be used on single-stage paint, gel coat, and clear coated paint surfaces. Whether you simply cruise the pavement or get down in the dirt Beadlock Pro ceramic paint coating can take the abuse. This easy-to-apply coating is specifically designed to protect your paint from the unique conditions it sees both on and off-road. This integrated SiO2 technology makes this product far more durable and hydrophobic than any wax or sealant.

How does it work? Beadlock Pro contains SiO2 (silica dioxide) which is the primary component of glass and is what gives glass its strength and hardness. Beadlock Pro ceramic paint coating creates a hard-sacrificial barrier which shields your paint from the abuse coming from the sun and other harsh elements.